1. code9ster's Avatar
    OK I tried to restore my Iphone 3gs it's Jail broken and base band is updated to 36.15.00.
    Everything went great then it rebooted and went to black screen. I restored it to 4.3.3 using Tinyumbrella with Tss server running to allow iTunes work around for installing 4.3.3 firmware. All worked but after it said it was finished went back to Dfu mode. I then used Ireb to fix boot issue used redsnow to boot into tethered mode and the iPhone booted up but, when the phone went to sleep after a minute went right back to dfu black screen. I am at a loss here on what to do. now the phone only goes to black screen can not hold power and home to force reboot or use redsnow, Ireb, or Fixboot. iTunes will not restore again. I get the error 1601 every time. I tried redsnow to start it and it will not reboot to finish the process. Nothing i do will restart the phone.

    Specs: Iphone 3gs running 4.3.3 custom firmware
    modem firmware 6.15.00
    jail broken with redsnow
    I do not have any shsh blobs


    Any help will be great.
    2011-08-22 12:39 AM
  2. Mes's Avatar
    Sorry, but if you "do not have any shsh blobs" you have two choices: the current version 4.3.5 or 4.1.

    Both 4.3.5 and 4.1 restores require a custom firmware restore because you have 6.15.x iPad BB installed.
    2011-08-22 01:03 AM
  3. code9ster's Avatar
    I have tried every link in Google for 4.1 ipsw and none work. I can't find any custom 4.3.5 ipsw's at this point just getting the phone back to a usable state works for me. do you have any idea where I can get the 4.1 ipsw I have an Att Sim
    2011-08-22 01:28 AM
  4. Mes's Avatar
    4.1 is preferred because it's fully jailbreakable. 4.3.5 is not.

    Use Snowbreeze v2.1 + stock iOS 4.1, and build your own custom 4.1 firmware.
    Continue w/Snowbreeze and enter 'pwnd-DFU'.
    Shift/select custom firmware and restore /iTunes
    If iTunes 10xx error, use Tiny Umbrella 'exit recovery' option.
    2011-08-22 01:35 AM
  5. code9ster's Avatar
    Trying it now hope it works. Thanks for the help so far keep checking back may need you soon.
    2011-08-22 02:23 AM
  6. Mes's Avatar
    You'll be fine.
    Good luck.
    2011-08-22 02:43 AM
  7. code9ster's Avatar
    keeps giving error 1600
    2011-08-22 06:04 AM
  8. Mes's Avatar
    Error 1600 means you're not getting into pwnd-DFU mode. This mode is required.
    From Snowbreeze, follow the count-down timer precisely.
    2011-08-22 06:08 AM
  9. code9ster's Avatar
    I have snow breeze shows i am in PWND mode and says open iTunes etc etc.If you get error unplug and start over. Which I have countless times. Might have to give in and just buy another one.
    2011-08-23 05:50 AM
  10. Mes's Avatar
    ?..If you get error unplug and start over....
    Re-download 4.1 stock firmware and Snowbreeze 2.1 (links in sig)
    Plug in phone, wait 1 minute. Ignore iTunes if it opens or closes.
    Hold power + home for 8-10 second. Notice high-low sound on computer and iPhone screen is blank.
    Run Snowbreeze, Simple Mode, build custom 4.1 firmware.
    Continue w/Snowbreeze, enter pwnd-DFU. Say yes to new boot-rom
    Do not unplug .....
    Load w/iTunes.
    2011-08-23 07:37 AM
  11. code9ster's Avatar
    followed your instructions now i am getting error 28.
    2011-08-23 08:41 PM
  12. Mes's Avatar
    Did your phone have water damage? Or other hardware issues?

    Error 28

    Hardware error. Return your device to Apple if possible. The problem is a bad dock connector on the iPhone. Must change the connector. If you have tried almost everything, reset the logic board (leave uncharged for five days or remove battery for half an hour), then pwn and restore. if this doesn't work, the "hard disk" of your iPhone is damaged

    iTunes Errors - The iPhone Wiki
    Try it again using the same process, change the cable, USB, and computer if possible.
    If the same error is reported it looks like a hardware problem.

    What is the first 5 digits of your serial number? Settings/General/About
    Last edited by Mes; 2011-08-23 at 08:56 PM.
    2011-08-23 08:45 PM
  13. code9ster's Avatar
    I can't see settings the screen stays black all the time and when i start to restore it turns white and thats it then goes back to black

    No water damage and never had an issue with it before
    2011-08-24 04:29 AM
  14. Mes's Avatar
    Do you have the receipt? The serial number is usually included.

    Maybe you know this: do you have an old or new bootrom?

    How old is your 3GS?
    2011-08-24 04:32 AM
  15. code9ster's Avatar
    I have the New bootRom.
    2011-08-24 04:24 PM
  16. Mes's Avatar
    I have the New bootRom.
    Good. The procedure was correct.
    Are you still getting iTunes error 28?
    2011-08-24 04:30 PM
  17. code9ster's Avatar
    yes still getting error 28
    2011-08-24 07:25 PM
  18. Mes's Avatar
    Sorry to hear that. The meaning of Error 28 has not changed.

    Error 28

    Hardware error. Return your device to Apple if possible. The problem is a bad dock connector on the iPhone. Must change the connector. If you have tried almost everything, reset the logic board (leave uncharged for five days or remove battery for half an hour), then pwn and restore. if this doesn't work, the "hard disk" of your iPhone is damaged

    iTunes Errors - The iPhone Wiki
    2011-08-24 07:27 PM
  19. code9ster's Avatar
    I almost have it. I get to Verifying restore with apple and it gives error something is blocking verification. what do i do for that?
    2011-08-25 06:15 AM
  20. code9ster's Avatar
    Got it going took restore but still booted black booted
    Tethered with redsnow and working as long as I don't
    Shut it off had to put 4.3.3 that's as far as it would let me
    Go back
    to get it working I had to take it apart and lift the motherboard from battery for hour then it stopped giving error 28 used Ireb to pwn dfu and tiny umbrella running TSS server to get past error 1600
    Big thank you to you Mes
    2011-08-25 04:00 PM
26 12
LINK TO POST COPIED TO CLIPBOARD