User Tag List

  1. Cowboy's Avatar
    This guide teaches you how to take apart an iPhone 4S. It is the same method for all models (CDMA and GSM).

    Supplies you will need:

    • Small Phillips screwdriver
    • Small Flat head screwdriver
    • Case opener tool
    • Pentalobe screwdriver (this is a 5 pointed star - newer iPhones have this instead of the standard Phillips)


    I also recommend having a nice clean and clear work space. It's a good idea to lay the screws and parts out as you pull them to keep them in order and make sure you don't forget or lose anything when putting the phone back together.

    Please remember before doing any work on the phone to power it off and pop the SIM tray out of the phone!

    Now to start work on the phone itself. First thing you will need to do is take out the two small screws at the bottom of the phone. They are on both sides of the dock connector. This is the only point where you will need to use the pentalobe screwdriver.



    Next there are two screws (where it is highlighted in blue) that need to be taken out. This will allow you to pop out the battery connector. The battery pops out by pulling up on the left side of the connector. There is a small piece convering the antenna so make sure not to lose that as well.



    Now that you have popped the connector pull up on the clear tab to take the battery out. Its a good idea to use a pry opener tools to help pull and pry the battery out. If the battery bends no worries they are made to do that

    With the battery removed we can now disconnect the dock connector. There are two screws holding it in place. It's also a good idea to pop up the antenna from the board as well!



    Once done with that remove the other 3 screws shown highlighted in red! The one in the bottom corner will require a flat head screw driver.



    Now lets move up the phone and take the protective shield off. There are 4 screws holding it in place. Once all 4 screws are out pry up on the shield and wiggle it out gently.



    Now lift up on the cables there will be 5 in all and pop out the camera! There are now 2 screw the need to come out. The one on the lift is hidden with some black tape and is sorta hidden the other is covering the last ribbon cable. Remove the screws along with both screws.



    There is now just one more screw left before you can pull the logic board. Once again you will need to use the flat head to remove this one.



    Once that screw is out lift up on the logic board and it should pop right out. ( Make sure you took the sim tray out first )

    Now that the board is out pry the vibrator up. I find using a flat blade box knife and sliding it underneath the motor works best. There is also one last screw that needs to be taken out to remove the dock!



    Now for the fun part taking out the 4 corner screws and the 6 with washers side screws. ( 10 Screws in all) Once you get them removed we can pop the front screen off!

    3 On the left same on the right


    Bottom


    Top


    Now pry the screen out.



    Voila! You have completed the take apart - have fun putting it back together.

    Last edited by Kyle Matthews; 2012-01-20 at 03:20 PM.
    2012-01-20 01:07 AM
  2. 2k1's Avatar
    Very Nice cowboy appreciate the work ya do
    2012-01-20 01:20 AM
  3. Cowboy's Avatar
    Thanks 2k1
    2012-01-20 02:29 AM
  4. Jcbzr's Avatar
    Very similar to the 4. Very educational.
    Since the little round module is the new vibrator motor, what is in the top right corner where the motor used to be?
    If I helped you in any way, please click on the button!
    2012-01-20 02:39 PM
  5. Greatbiguns's Avatar
    NICE JOB Cowboy!!
    That is an Awesome Tutorial, and great photos along the way!!
    THANKS
    2012-01-20 05:53 PM
  6. Geenius's Avatar
    Nice Job, Very clear and easy to follow!

    Thank You!
    2012-01-21 07:43 AM
  7. matthew1111's Avatar
    Nice! I would thank but on the iPhone right now haha

    So you have to take it ALL apart for the front? D:
    Ik the back is easy you only have to take the backing off
    That Thanks button is there for a reason!

    2012-02-07 04:50 AM
  8. imprezzivesti's Avatar
    what steps need to be added to swap the mid frame to a new one on the 4s??
    2012-04-20 04:41 AM
  9. Cowboy's Avatar
    I'll see if I can't write one up soon been busy
    2012-04-20 05:52 AM
  10. imprezzivesti's Avatar
    That would be awesome when u have the time, even just written instructions or a link to some for the time being would help a bunch. That original tutorial helped me so much on my first screen repair now I really wanna try a midplate swap but I haven't the slightest clue where to begin because I can't track instructions down anywhere and don't wanna mess my phone up.
    Last edited by imprezzivesti; 2012-04-20 at 05:11 PM.
    2012-04-20 06:10 AM
  11. Cowboy's Avatar
    I been meaning to do one just have to find the time
    2012-05-08 03:20 AM
  12. Cowboy's Avatar
    But they are of the highest quality
    2012-05-09 04:00 PM
  13. Cowboy's Avatar
    4 or 4S?
    2012-05-10 12:08 AM
  14. Cowboy's Avatar
    wholesalegadgetparts aren't bad
    2012-05-13 02:59 AM
  15. TheLXD's Avatar
    i have a 4s and i need instructions on how to swap the midplate...im sitting here with everything apart and kinda worrying cuz this is my only phone please help!!
    2012-11-18 09:13 PM
  16. Cowboy's Avatar
    Where you stuck at? Or having problems with
    2012-11-18 11:18 PM
  17. mangetsu's Avatar
    hey cowboy i just replaced my iphone 4s screen, but the touchscreen doesnt work, hopefully you could tell me if i missed something
    2013-04-30 09:16 PM
  18. Cowboy's Avatar
    Check your connections
    2013-04-30 09:27 PM
LINK TO POST COPIED TO CLIPBOARD